CHARACTERIZATION OF OIL SHALE PROCESSING RESIDUES AND SEPARATED PRODUCTS; pp. 500–512Full article in PDF format | doi: 10.3176/oil.2009.4.06
Different residues of Huadian oil shale processing were investigated. Their inorganic chemical composition and phase structural characteristics were identified by X-ray fluorescence spectrometry (XRF) and X-ray diffractometry (XRD). The influence of calcination conditions on processing residues at different ash activation degrees and impurities' leaching rates as well as the quality of obtained SiO2 concentrate were investigated by a single-factor method. The results showed that only circular crossflow-type retorting-derived semicoke has different phase-structural characteristics at different calcination temperatures. In the range of 700–800 °C, the leaching rate of aluminum and iron reaches the maximum. To prepare SiO2 concentrate, starting material should be calcined for 1.5 h at 700–800 °C. As a result, SiO2 concentrate which meets the national standard of silica white will be obtained; the content of SiO2 is 92.34% and its specific surface area 104 m2/g. Phase structures of Fushun-type retorting residue and cogeneration power plant ash did not change dramatically at different calcination temperatures. The leaching rate of Al and Fe reached the maximum. Further calcination is unnecessary in reutilization, only removal of impurities by means of acid soaker is relevant. Fushun-type retorting residue can also be used to make SiO2 concentrate which meets the national standard; the content of SiO2 is 90.38%, its specific surface area is 91 m2/g. The leaching rate of aluminum from cogeneration power plant ash is lower, and this ash cannot be used to prepare silica white meeting the national standard. It can be applied as an ingredient of cement, at brick preparation, etc. Separation and purification products are a mixture of crystalline SiO2 and amorphous SiO2, while the content of crystalline SiO2 is 32.2%.
1. Hilger, J. Combined utilization of oil shale energy and oil shale minerals within production of cement and other hydraulic binders // Oil Shale. 2003. Vol. 20, No. 3. P. 347–355.
2. Grinberg, A., Keren, M., Podshivalov, V., Anderson, J. Producing electricity from Israeli oil shale with PFBC technology // Oil Shale. 2000. Vol. 17, No. 4. P. 307–312.
3. Shurtleff, J. K., Cowley, S. Apparatus, System, and Method for In-situ Extraction of Oil from Oil Shale // US, 1662726, 2007-03-15.
4. Al-Otoom, A. Y., Shawabkeh, R. A., Al-Harahsheh, A., M., Shawaqfeh, A. T. The chemistry of minerals obtained from the combustion of Jordanian oil shale // Energy. 2005. Vol. 30, No. 5. P. 611–619.
5. Smadi, M. M., Haddad, R. H. The use of oil shale ash in Portland cement concrete // Cement Concr. Compos. 2003. Vol. 25, No. 1. P. 43–50.
6. Holopainen, H. Experience of oil shale combustion in Ahlstrom pyroflow CFB-boiler // Oil Shale.1991. Vol. 8, No. 3. P. 194–209.
7. Wang Qing, Bai Jingru, Sun Baizhong, Sun Jian. Strategy of Huadian oil shale comprehensive utilization // Oil Shale. 2005. Vol. 22, No. 3. P. 305–315.
8. You Jun-jun, Ye Songqing, Liu Zhao-jun, Wang Yun-zhe. Comprehensive development and utilization of oil shale // Geology of the World. 2004. Vol. 24, No. 3. P. 251–256 [in Chinese].
9. Liu Zhao-jun, Liu Rong. Oil shale resource state and evaluation system // Earth Science Frontiers. 2005. Vol. 12, No. 3. P. 315–323 [in Chinese].
10. Li Shuyuan, Qian Jialin, Wang Jianqiu. 27th International Oil Shale Conference summary report // Chinese Journal of Oil Shale. 2007. No. 5. P. 22–27 [in Chinese].
11. Li Yong, Feng Zong-yu, Xue Xiang-xin, He Yan, Qiao Gui-bo. Ecological utilization of oil shale by preparing silica and alumina // Journal of Chemical Industry and Engineering. 2008. Vol. 59, No. 4. P. 1501–1057 [in Chinese].
12. Wang Qing, Huan Xiankun, Liu Hong-peng, Sun Ba-izhong, Jia Chun-xia. Microwave induced pyrolysis of Huadian oil shale // Journal of Chemical Industry and Engineering. 2008. Vol. 59, No. 5. P. 1288–1293 [in Chinese].
13. Arro, H., Prikk, A., Pihu, T., Öpik, I. Utilization of semi-coke of Estonian shale oil industry // Oil Shale. 2002. Vol. 19, No. 2. P. 117–125.
14. Li Yong, Xue Xiang-xin, Feng Zong-yu. Preparation of precipitated silica from oil shale residue // The Chinese Journal of Process Engineering. 2007. Vol. 7, No. 4. P. 751–754 [in Chinese].
15. Li Lai-shi, Zhai Yu-chun, Qin Jin-guo. Extracting high-purity alumina from fly ash // Journal of Chemical Industry and Engineering. 2006. Vol. 57, No. 9. P. 2189-2193 [in Chinese].
16. Tan Xin, Wang Fu-liang, Wang Rong-sheng. Study on preparation of white carbon black from deoiled residue of oil shale // Mining & Metallurgy. 2004. Vol. 13, No. 1. P. 59–63 [in Chinese].
17. Trikkel, A., Kuusik, R., Maljukova, N. Distribution of organic and inorganic ingredients in Estonian oil shale semicoke // Oil Shale. 2004. Vol. 21, No. 3. P. 227–236.18. Xu Ying-Mei, He De-Min, Wang Dong-Mei, Lian Yu-Huan, Guan Jun, Zhang Qiu-Min.Influence of calcination temperature on leaching rate of aluminum and iron impurities in oil shale ash // Oil Shale. 2009. Vol. 26, No. 2. P. 163–168.
Back to Issue