ESTONIAN ACADEMY
PUBLISHERS
eesti teaduste
akadeemia kirjastus
cover
Estonian Journal of Engineering
Wear performance of PVD coated tool steels; pp. 202–210
PDF | doi: 10.3176/eng.2012.3.05

Authors
Aleksei Tshinjan, Heinrich Klaasen, Jakob Kübarsepp, Eron Adoberg, Fjodor Sergejev, Adolf Talkop
Abstract

The paper describes the performance of high alloy tool steels coated by PVD techniques. Performance evaluation was based on the wear resistance in the conditions of prevalence of adhesion and on tool wear (durability) in the conditions of blanking of electrotechnical sheet steel. Hardmetal (WC-15% Co) was used as a primary standard material. It is shown that adhesive wear resistance depends both on the composition of the PVD coating and on that of the tool material to be coated – steels with higher adhesive wear resistance ensure also a higher strengthening effect of the surface. Sharpening of specimens (cutting tools) – removal of coating at the face zone of the tool by grinding – revealed the difference in the efficiency of the coating in different zones of the tool. In terms of durability, thin PVD coatings do not enable improvement of the performance of sheet metal blanking tools (dies, punches). No correlation between durability in blanking and adhesive wear resistance was revealed. In terms of durability prognostication, alloys’ (tool steels, hardmetals, cermets) adhesive wear resistance enables tool life assessment only when materials of similar nature (steels, carbide composites) are compared.

References

  1. Rickerby, D. S. Advanced surface coatings. In A Handbook of Surface Engineering (Matthews, A., ed). Blackie and Sons, London, 1991.
http://dx.doi.org/10.1007/978-94-011-3040-0

  2. Protective Coating and Thin Films. Kluwer Academic Publications, Dordrecht, 1997.

  3. Hogmark, S., Jacobson, S. and Larsson, M. Design and evaluation of tribological coatings. Wear, 2000, 246, 20–33.
http://dx.doi.org/10.1016/S0043-1648(00)00505-6

  4. ASM Handbook, vol. 5: Surface Engineering (Cotell, C. H., Spraque, J. A. and Smitt, F. A., eds). ASM International, USA, 1994, 900–908.

  5. Burnett, P. J. and Rickberg, D. S. The erosion behaviour of TiN coating on steel. J. Mater. Sci., 1988, 23, 2429–2443.
http://dx.doi.org/10.1007/BF01111900

  6. Dobrzanski, L. A. and Adamiak, M. Structure and properties of TiN and Ti(C,N) coatings deposited in the PVD process on high-speed steels. J. Mater. Process. Technol., 2003, 133, 50–62.
http://dx.doi.org/10.1016/S0924-0136(02)00206-6

  7. Sergejev, F., Peetsalu, P., Sivitski, A., Saarna, M. and Adoberg, E. Surface fatigue and wear of PVD coated punches during fine blanking operation. Eng. Failure Anal., 2011, 18, 1689–1697.
http://dx.doi.org/10.1016/j.engfailanal.2011.02.011

  8. Hua, M., Ma, H. Y., Mok, C. K. and Li, J. Tribological behaviour of patterned PVD TiN coatings on M1 steel. Tribol. Lett., 2004, 17, 645–653.
http://dx.doi.org/10.1023/B:TRIL.0000044515.75066.b4

  9. Wilson, S. and Alpas, A. T. TiN coating wear mechanisms in dry sliding contact against HSS. Surf. Coat. Technol., 1990, 108109, 369–376.
http://dx.doi.org/10.1016/S0257-8972(98)00593-3

10. Carlsson, P. and Olsson, M. PVD coatings for sheet metal forming processes – a tribological evaluation. Surf. Coat. Technol., 2006, 200, 4654–4663.
http://dx.doi.org/10.1016/j.surfcoat.2004.10.127

11. Technical Specification Guide CEN/TS 1071-8:2004. Advanced technical ceramics. Methods of test for ceramic coatings. Rockwell indentation test for evaluation of adhesion. European Committee for Standardization, 2005.

12. Klaasen, H., Kübarsepp, J. and Eigi, R. Pecularities of hardmetals wear in blanking of sheet metals. Tribology Int., 2006, 39, 303–309.
http://dx.doi.org/10.1016/j.triboint.2005.01.041

13. Klaasen, H. and Kübarsepp, J. Wear of advanced cemented carbides for metalforming tool materials. Wear, 2004, 256, 846–853.
http://dx.doi.org/10.1016/j.wear.2003.08.004

14. Schmidt, R. A., Birzer, F., Höfel, B., Hellmann, M., Reh, B., Rademacher, P. and Hoffmann, H. Cold forming and fineblanking. In A Handbook of Cold Processing, Steel Material Properties, Component Design. Carl Hanser Verlag, München-Wien, 2007.

15. Klaasen, H., Kübarsepp, J., Tšinjan, A. and Sergejev, F. Performance of carbide composites in cyclic loading wear conditions. Wear, 2011, 271, 837–841.
http://dx.doi.org/10.1016/j.wear.2011.03.005

Back to Issue

Back issues