ESTONIAN ACADEMY
PUBLISHERS
eesti teaduste
akadeemia kirjastus
cover
Estonian Journal of Engineering

Analysis of surface roughness parameters achieved by hard turning with the use of PCBN tools; pp. 88–99

Full article in PDF format | doi: 10.3176/eng.2011.1.09

Author
Anna Zawada-Tomkiewicz

Abstract
The turning of hardened steels has been applied in many cases in production. Currently, the most important problem is concerned with the properties of the surface finish. This paper investigates the effect on surface finish in a continuous dry turning of hardened steel when using polycrystalline cubic boron nitride tools. The surface profiles (2D arrangement) and surface topography (3D arrangement), generated during the hard turning operation on an EN 41Cr4 low chromium alloy steel, heat treated to the hardness of 58 HRC, were evaluated. This paper intro­duces the multiparameter characterization of the surface when cutting with different tool materials.
References

  1. Zawada-Tomkiewicz, A. Machined surface quality estimation based on wavelet packets parameters of the surface image. PAK (Poland), 2010, No. 6, 606–609.

  2. Alegre, E., Alaiz-Rodríguez, R., Barreiro, J. and Ruiz, J. Use of contour signatures and classification methods to optimize the tool life in metal machining. Estonian J. Eng., 2009, 15, 3–12.
doi:10.3176/eng.2009.1.01

  3. Grzesik, W. and Wanat, T. Comparative assessment of surface roughness produced by hard machining with mixed ceramic tools including 2D and 3D analysis. J. Mater. Process. Technol., 2005, 169, 364–371.
doi:10.1016/j.jmatprotec.2005.04.080

  4. Klocke, F., Brinksmeier, E. and Weinert, K. Capability profile of hard cutting and grinding processes. Ann. CIRP, 2005, 54, 2005, 22–45.

  5. Özel, T. Computational modelling of 3D turning: Influence of edge micro-geometry on forces, stresses, friction and tool wear in PcBN tooling. J. Mater. Process. Technol., 2009, 209, 5167–5177.
doi:10.1016/j.jmatprotec.2009.03.002

  6. Dong, W. P., Sullivan, P. J. and Stout, K. J. Comprehensive study of parameters for charac­terizing three dimensional surface topography, III. Parameters for characterizing amplitude and some functional properties. Wear, 1994, 178, 29–43.

  7. Stout, K. J., Sullivan, P. J., Dong, W. P., Mainsah, E., Luo, N., Mathia, T. and Zahouani, H. The Development of Methods for the Characterisation of Roughness in Three Dimensions. Publication No. EUR 15178 EN, Commission of the European Communities, Luxembourg, 1994.

  8. Storch, B. Zjawiska przykrawędziowe i monitorowanie chropowatości powierzchni po obróbce jednoostrzowej. Monograph 124, Koszalin University of Technology, 2006.

  9. Kishawy, H. A. and Elbestawi, M. A. Effects of process parameters on material side flow during hard turning. Int. J. Machine Tools Manufact., 1999, 39, 1017–1030.
doi:10.1016/S0890-6955(98)00084-4

10. Liu, K. and Melkote, S. N. Effect of plastic side flow on surface roughness in micro-turning process. Int. J. Machine Tools Manufact., 2006, 46, 1778–1785.
doi:10.1016/j.ijmachtools.2005.11.014

11. Chen, W. Cutting forces and surface finish when machining medium hardness steel using CBN tools. Int. J. Machine Tools Manufact., 2000, 40, 455–466.
doi:10.1016/S0890-6955(99)00011-5

12. Rech, J. and Moisan, A. Surface integrity in finish hard turning of case-hardened steel. Int. J. Machine Tools Manufact., 2003, 43, 543–550.
doi:10.1016/S0890-6955(02)00141-4

13. Zawada-Tomkiewicz, A. and Storch, B. The analysis of the state of turned surface with the use of its image. In Contact and Surface, WIT Press, Southampton, 2009, 97–104.

14. Outeiro, J. C., Dias, A. M. and Jawahir, I. S. On the effects of residual stresses induced by coated and uncoated cutting tools with finite edge radii in turning operations. Ann. CIRP, 2006, 55, 111–116.
doi:10.1016/S0007-8506(07)60378-3

15. Poulachon, G., Bandyopadhyay, B. P., Jawahir, I. S., Pheulpin, S. and Seguin, E. Wear behavior of CBN tools while turning various hardened steels. Wear, 2004, 256, 302–310.

16. Yallese, M. A., Chaoui, K., Zeghib, N., Boulanouar, L. and Rigal, J.-F. Hard machining of hardened bearing steel using cubic boron nitride tool. J. Mater. Process. Technol., 2009, 209, 1092–1104.
doi:10.1016/j.jmatprotec.2008.03.014

17. Pavel, R., Marinescu, I., Deis, M. and Pillar, J. Effect of tool wear on surface finish for a case of continuous and interrupted hard turning. J. Mater. Process. Technol., 2005, 170, 341–349.
doi:10.1016/j.jmatprotec.2005.04.119

18. Zawada-Tomkiewicz, A. and Storch, B. Measurement of tool flank wear with the use of white light interferometr. PAK (Poland), 2010, No. 8, 950–953.
Back to Issue